Yes. Pursuant to section 98.0422 of the Los Angeles City Municipal Code, expedite review process is available for the amount of the fee equal to one-half of the review fee, in addition to the normal review fee.

All equipment approved by LADBS-ETL, with some exceptions for some of the equipment that have General Approvals, are required to bear the approval label of LADBS-ETL. This approval label would be different from equipment that is approved under Laboratory or General Approval vs. Field one-time approval.

For equipment that has Laboratory Approval or General Approval, the applicant is required to submit the following:

1. A completed label application form (PC-ELEC-App.12). Original signature is required.
2. Indicate the quantity of equipment that will be manufactured during the approval period.
3. Indicate the quantity of labels.
4. Application fee as determined based on unit fee cost for each label. Make check payable to “The Department of Building and Safety, City of Los Angeles.”

Check the equipment approval letter. Every approval letter indicates the models that are included. You may check the approval letters on the "LA Research Reports" page.

The steps are the same as regular approval, as follows:

Submit the following:

1. A completed application form (PC-ELEC-App.12). Original signature is required.
2. Application fee as marked on application form. Make check payable to “The Department of Building and Safety, City of Los Angeles.”
3. Current product literature (brochure, operational instruction, maintenance manual, owner’s manual).
4. Photographs or drawings showing the exterior views and internal views of the equipment.
5. Schematic wiring diagrams. Diagrams should identify the sizes of wires, ratings of fuses, circuit breakers, and other components.
6. The parts list for the components operating at or above 30 VAC or 24.8 VDC in dry locations or 15 VAC or 12.4 VDC in wet locations. Include the part's function, name of manufacturer, catalog number, electrical ratings, and testing agency component recognition or listing number.
7. Production sample of the equipment as follows:

• For General or Laboratory Approval: Submit a current production sample (complete and operable) with all appurtenances to operate the equipment. If the equipment is too heavy or large to ship to the laboratory, arrange for a field location in the City of Los Angeles or at the factory where a complete testing can be performed without on-site restrictions (call the laboratory for a prior arrangement) and pay for the field trip charges.
• For One-Time Approval of field installed equipment: Provide the field location where the equipment is intended to be installed insuring that it can be evaluated and tested without on-site restrictions. Provide the complete address, phone number, and contact person. Pay for the field trip charges.

However, the revised approval may require a new model designation of the previous product and the approval would be for the duration that was originally established for the equipment.

An approved recognized electrical testing agency is a testing agency that obtains approval from the Department of Building and Safety to perform testing and listing and field evaluation. A list of these recognized testing agencies are posted on the LADBS web as follows on the "Electrical Test Lab (ETL)" page:

• Testing agencies that have approval for listing of equipment
• Testing agencies that have approval for one-time field evaluation

Only products that have either a Laboratory or General Approval (no one-time approvals) may be subject to annual renewal. About 60 days before an approval expires, the original applicant needs to take the following actions:

1. Submit a completed renewal application form (PC-ELEC-App.12). Original signature is required.
2. Submit the application fee as marked on the application form. Make check payable to “The Department of Building and Safety, City of Los Angeles.”
3. Submit a current production sample of the equipment along with an explanation if there were any changes to the equipment from the previous approval.

Make sure that the equipment approval has not expired by checking the equipment approval letter. Each letter has an approval and expiration date that is indicated on the top right hand of the letter.

1. Laboratory Approval – This approval is intended for mass produced electrical products by manufacturers.
2. Field One-Time Approval – This approval is intended for field installed products that may be one of a kind or a modified mass produced product. This type of approval is limited to the field conditions, intended for a specific job address.
3. General Approval – This approval is intended for products that may have code violations, have no recognized national safety standards to test to, or tested only to manufacturer standards. This approval may be for mass produced products, one of kind products, or for a job at a specific address. This approval may be referred to as “Research Report”.

There is one application form that is used for each type of submittal (New, Renewal, Technical and Clerical Modifications, for Laboratory, General, and One-time Approvals). You can obtain this form as follows:

• On the LADBS website here as PDF (PC-ELEC-App.12) or on the "Electrical Test Lab (ETL)" page.
• Contact City of Los Angeles Electrical Test Lab at 213-482-6721.

Submit the following:

1. A completed application form (PC-ELEC-App.12). Original signature is required.
2. Application fee as marked on application form. Make check payable to “The Department of Building and Safety, City of Los Angeles.”
3. Current product literature (brochure, operational instruction, maintenance manual, owner’s manual).
4. Photographs or drawings showing the exterior views and internal views of the equipment.
5. Schematic wiring diagrams. Diagrams should identify the sizes of wires, ratings of fuses, circuit breakers, and other components.
6. The parts list for the components operating at or above 30 VAC or 24.8 VDC in dry locations or 15 VAC or 12.4 VDC in wet locations. Include the part's function, name of manufacturer, catalog number, electrical ratings, and testing agency component recognition or listing number.
7. Production sample of the equipment as follows:
   1. For General or Laboratory Approval: Submit a current production sample (complete and operable) with all appurtenances to operate the equipment. If the equipment is too heavy or large to ship to the laboratory, arrange for a field location in the City of Los Angeles or at the factory where a complete testing can be performed without on-site restrictions (call the laboratory for a prior arrangement) and pay for the field trip charges.
   2. For One-Time Approval of field installed equipment: Provide the field location where the equipment is intended to be installed insuring that it can be evaluated and tested without on-site restrictions. Provide the complete address, phone number, and contact person. Pay for the field trip charges.
8. For equipment with unlisted transformers, drivers or power supplies with a rating of less than 1KVA, provide two samples with schematic wiring diagrams and specification sheets.